Welcome to Shenzhen Xinsong Hengli Automation Equipment Co., Ltd.!

Intelligent electric screwdriver

News

contact us

Shenzhen Xinsong Hengli Automation Equipment Co., Ltd.

Contact: 13510839855 (Mr. Mo)

Business: 18076545681 (Liu Zhenxin)

Business: 15112331270 (Chaijinjin)

Tel: 0755-28121215

Fax: 0755-28121315

Email: sinsoholly@163.com

QQ: 2129524050 3188820898

Website: www.szxshl.com

Address: 402-403, Hesheng Wenchuang Park, Hebei Industrial Zone, Dalang South Road, Longhua District, Shenzhen, Guangdong, China


Non-standard automatic soldering machine: soldering station can not be too saturated when soldering

Your current location: Home >> News >> Industry news

Non-standard automatic soldering machine: soldering station can not be too saturated when soldering

Release date:2018-06-28 Author:admin Click:

Non-standard automatic soldering machine manufacturers introduce soldering machine solder joints can not be too saturated

When the soldering machine is soldered, the solder joints should not be too saturated, and the tin dots are too large to be easily disconnected from the adjacent solder joints. In soldering, solder joints should not be too tin-saving, which leads to the occurrence of solder joints. The correct automatic soldering machine solder joint is in the middle of three or four points. The solder should be semi-circular with the component legs. It is not saturated and does not save tin. It seems that the solder joints are the best contact with the components. The board is also the most neat. Non-standard automatic soldering machine manufacturers soldering machine using adjustable balance temperature soldering iron is better; usually do not use a soldering iron, to keep a certain amount of tin on the soldering iron mouth, do not clean the soldering iron mouth on the sponge and store it on the iron frame The sponge needs to maintain a certain amount of water until the sponge is wet all day; when the soldering iron is used, the tip must be cleaned.

The soldering machine does not need to take the soldering iron tip to the sponge for cleaning during use. Just put the tin on the soldering iron mouth into the tin-collecting carton, so that the temperature of the soldering iron nozzle will not drop rapidly, if there is still on the IC It is difficult to extract tin, and some tin is added (because the flux contains tin flux), it is easy to extract more tin down; the temperature of the soldering iron is between 340 and 380 degrees, if some sensitive components are only acceptable 240~280 degree soldering temperature; the soldering iron mouth is not suitable for metal parts such as blades, but it should be solved with tin wire; after using it every day, clean it first, then add enough tin, and then cut off the power immediately.


自动焊锡机


焊锡机引线不宜过细过长,焊接时的电压降不得大于初始电压的5%,初始电压不能偏离电源电压的±10%。焊机操作时应戴手套、围裙和防护眼镜,以免火星飞出烫伤。滑动部分应保持良好润滑,使用完后应清除金属溅沫。非标自动焊锡机厂家新焊机开始使用24小时后应将各部件螺丝紧固一次,尤其要注意铜软联和电极之间联接螺丝一定要紧固好,用完后应经常清除电极杆和电极臂之间的氧化物,以保证良好接触。

自动焊锡机使用时如发现交流接触器吸合不实,说明电网电压过低,用户应该首先解决电源问题,电源正常后方可使用。需要指出的是,新购买的焊机半个月内如出现主件质量问题,可以更换新的焊机或者更换主件。焊锡机主机部分保修一年,长期提供维修服务。一般情况下用户通知厂方后,根据路程远近三到七天内服务到位。由于用户原因而造成的焊机损坏不在保修范围内。易损件、消耗件不在保修范围内。


This article URL:http://en.szxshl.com/news/354.html

Contact us

Shenzhen Xinsong Hengli Automation Equipment Co., Ltd.

1.png0755-281212152.png2129524050
3.png135108398554.pngsinsoholly@163.com
Follow us

share it One key to share
Welcome to leave a message
Please enter your message here and we will contact you as soon as possible.
name
name
tel
tel
email
email
address
address